Tie Down Engineering G5 Stainless Steel Disc Brakes
- 3500# Axle 5 Lug 9.6" Rotor, For 13", 14" or 15" Wheels, Replaces 10" Drum Brakes.
- All Aluminum Caliper: 380 series Aluminum w/E-Coat, sheds heat five times faster than cast iron
- 304 Stainless Steel Rotor with Venting Holes, Diameter: 9.6" x .3125"
- Pre-greased hub includes bearings& seal. Uses lithium based or lithium compatible.
- Hub Specs: 1,750#cap, 5 on 4.5" Hub Finish - GalvX
- Bearing Size: Outer 1 1/16" (L44649) Inner 1 3/8" (L68149)
- includes mounting bracket and lug nuts
Technical Infomation for G5 Disc Brakes:
Here's Eleven Great reasons to buy Tie Down Engineering G5 brakes :
- All Aluminum Caliper: 380 series Aluminum w/E-Coat, sheds heat five times faster than cast iron
- Ceramic Pads: Floating ceramic pads with stainless steel backing plates. Improved wear over organic pads. Lifetime limited warranty.
- 304 Stainless Steel Rotor with Venting Holes: New laser cut venting holes assist in faster cooling
- Slim Design: Allows short axle overhangs and provides direct brake line routing to the axle
- Bi-metal Pistion: Combines a stainless steel outer pistion with an aluminum inner sleeve to shed braking heat fast. The stinless steel outer piston will not rust or corrode.
- Oversize Rubber Boot: 50 percent thicker by design to provide a positive faster piston witdrawal.
- Rotating Swivel Brake Line Connector: Swivel brake connector allows for convenient and simple brake line placement.
- Stainless Steel Caliper Pins with Oil Impregnated Bronze Bushings: Allows caliper to float freely and ensures proper alignment during installation and will not rust or corrode.
- Vented Caliper Housing: Improves heat disspation and decreases pad wear.
- One Piece Stainless Steel Bleeder Valve with Teflon Coating: Will not corrode and allows for easier bleeding of brake system.
- Square O-ring with Slant Angle: Helps retract pistons away from the rotor when fluid pressure is released. Provides better protection from contamination of brake fluid.
Tie Down Engineering Part # 82091, Tie Down G5 Brakes - One Wheel Set - Integral Hub and Rotor - Stainless Steel Finish
 Tie Down Engineering G5 Disc BrakeTechnical Information
Tie Down Engineering Brake Fluid Technical Information
We Also Stock Tie Down Engineering Disc and Drum Brakes, Actuators, Brake Accessories, Axles, Spindles, Hubs, Bow and Winch Mounts, Bearing kits, Boat Guides, Fenders, Eliminator Torsion Axles, Leaf Spring Axles, Axle Plates, Bearings, Cups, Seals and Caps, Bearing Protectors and Covers, Bolster Brackets, Bow Chains, Bow Guides, Brake Lines,
Bunk and Trailer Brackets, G5 Stainless Steel Disc Brakes, Hydraulic Drum Brakes, Vented Disc Brakes, Vented Disc Brake Kits, Bunk Brackets, Bunk Rollers, Bunk Stiffening Bars, Cables Winch, Caps,
Channel Brackets, End Units, Hub and Spindle, Eliminator Vented Disc Brakes, Eliminator Vented Disc Brake Kits, Equalizers, Leaf Springs, Frames, Fenders, Custom Fenders, Metal Fenders, Modular Fenders, Fender Mounting Brackets, Plastic Fenders,
Frame Tie Down Brackets, Hitch Balls, Hitch Cables, Hooks, Idler Hubs, Hubs, Super Lube Hubs, Spindle End Units, Turbo Lube Hubs, Hull Sav’r Products, Hull Sav'r Rollers, Hull Sav'r Black PVC Molded Rollers, Keel Rollers, Keel Roller Brackets, Keel Brackets, Leaf Springs, Light Brackets, Motorcycle Rails and Ramps, Panel Brackets including Split Panel, Pivot Brackets, Pivot Rollers, Pivot/Swing Tongues, Pivot Weldment Bracket, Pontoon Bunk Brackets, Pull Pins, Rollers, Roller Shafts, Safety Chains and Cables, Seals, Side Guide Bracket, Springs, Track Rollers, Axle Spring Hangers, Equalizer
Springs, Leaf Springs, Solenoids, Spare Tire Carriers, Eliminator Spindles, Spindles Super Lube, Torsion Spindles, Square Stub Spindles,
Super Lube Hubs/Spindles, Swing/Pivot Tongues, Swivel Brackets,Tail Light Mounting Brackets, Tire Carriers, Tire Carriers Torsion Axle, Tongue Support Bracket, Tongue Skid, Trailer Bow Stands, U-Bolt Kits, Vertical Heavy Duty Brackets, Winch Cables, Winch Straps, Winch Mounts and Wobble Rollers
|
